CX-13
v1.02 - Controller for up to 4 COMETCH, AWV314 Conrad or RIMAX
2.4GHz wireless FM A/V modules
   
  |
    
    
|
With help of CX-13 controller
any ATV repeater can use up to four COMTECH
2,4GHz, CONRAD
AWV314 2.4GHz, or RIMAX
rx and/or tx modules.
2002-01-18
CX-13 2.3GHz RTX software v1.00 released.
2005-01-01
CX-13 2.3GHz RTX software v1.02 released ( RS232
remote control added ).
Order
CPU & PCB source files
Simply reconnect I2C buses
on to CX-13 module, and enjoy.
CX13
software supports:
- one VFO available for each
rx/tx, freqency range unlimited, VFO step 250 KHz.
- real time displaying of
PLL LOCK, INSTALL, I2C ERROR state, plus rx/tx mode.
- install/uninstall any
rx/tx.
- switch rx/tx on/off manualy
at setup process.
- single wire remote switch
for each rx/tx device, on/off.
- set each device controll
in to rx or tx mode.
- tune LCD contrast via
keyboard (driving voltage goes from +1.8 down to -1.8v).
- tune LCD LED backlight
via keyboard.
- any setup data can be
stored in to internal EEPROM.
- power_on command for total
reset.
- automatic total reset
at 1st run.
- software name, release
date and version displayed after power ON.
- full remote controll &
adjust for almost all functions
- software uses double line
Hitachi compatible 2x40 LCD's with LED backlight.
- LCD can be omit-ed. CX13
will operate well without connected LCD and/or keyboard.
- extra reset logic build
in.
- PLL support for: Philips
TSA-5055T, Mitel SP5055S.
- serial port RS232
9600bps 8N1
- supply voltage from +11
up to +15v.
- low power consumption
(43mA @12v Stand_by, 110mA @ 12v All ON).
Comands on CX-13 keyboard:
| CX13 v1.00 | DOWN | UP | FUNCTION | MEMORY |
| Power ON cmd : | - | - | Total INIT | - |
| Normal : | - | - | Software info | SELECT device |
| Menu SET : | Device OFF | Device ON | Enter SETUP mode | - |
| Menu VFO : | Frequency DOWN | Frequency UP | Next menu | Store |
| Menu DEVICE : | Uninstall | Install | Next menu | Store |
| Menu TYPE : | RX device | TX device | Next menu | Store |
| Menu LCD : | Contrast - | Contrast + | Next menu | Store |
| Menu BCK : | BackLight - | BackLight + | Exit setup | Store |
Available RS232 comands ( firmware v1.02 ):
[C] check
status - print current data
shown on LCD (device type, frq., lock status, ena state,...)
[D] dis/ena
device - disable / enable any device,
temporarly or permanent
[F] adjust
frq. - change VFO frq
on any device and save. Prints: device type, frq., PLL lock status.
[H] help
- available RS232 commands
[I] info
- print software info
[L] LCD
backlight - adjust or switch LCD
backlight off
[R] restore
- restore all data from EEprom
[T] device
type - assign Rx or
Tx RF module to any device
[X]
EEprom Hex DUMP - print content of CPU's eeprom
area
[@] restart
CX-13 - remote restart
UNI13P
v2.02 - Controller for COMETCH, AWV314, RIMAX and other 1.2
& 2.4GHz wireless FM A/V modules
    
    
   |
|
RIMAXmodules uses an Themic U6239B PLL (almost compatible with 5055) Their factory predefined channels were on 2434, 2453, 2473 and 2410 MHz. Our UNI13P/CX13/ATV13P controllers can be connected directly on to PLL chip, after cuting off original - onboard CPU. Samples we've tested were operational within 2360 - 2503 MHz.     
  |
Do you have COMTECH
1.2GHz or 2,4GHz wireless FM modules, 2.4GHz AWV314 (Best
No. 351040) from CONRAD,
or RIMAX modules
and don't know how use them on 23cm, 13cm, 6cm, or on 3cm for ATV ?
- MATCO
(USA) EzATV
(USA) WIMO
(DL) folow this link
, PICOTRONIC
(France) F1GE
INFRACOM (France)
Note: MATCO also trade
an chip realtime color PAL/NTSC QUAD. Useful for ATV repeater, etc ...
COMTECH modules - pin description
| TX
module
1 = RF OUT
|
RX
module
1 = n.c.
|
New:
2000-09-27 UNI23PFL 1.2GHz RTX software v2.02 released.
Order
CPU & PCB source files
UNI13P
project will give you all you need for ATV... Just simply reconnect I2C
bus on to UNI13P module, and enjoy.
UNI13P
software now supports: all Comtech modules (23cm, 13cm) & Conrad 13cm
modules AWV314.
- 23cm: one VFO available,
freqency range from 0.800 up to 2.100 GHz, VFO step 250 KHz.
- 13cm: one VFO available,
freqency range from 2.000 up to 2.700 GHz, VFO step 250 KHz.
- 3cm: one VFO available,
LCD frq. range: 10.000 - 10.800 GHz (actual step 125kHz, 2500-2700 MHz),
LCD step 0.500 MHz.
Available preprogrammed UNI13P CPU's
- 23cm
dual mode soft.
in one CPU : UNI23PFL for 1.2GHz
ATV
TX & RX user selectable RX or TX at Power_ON .
- 13cm
dual mode
soft. in one CPU : UNI13PFL for
2.4GHz ATV TX & RX user selectable RX or TX at Power_ON
.
- 6cm software version :
UNI57PTL
for 6cm ATV TX 13cm frq. must be multiplied externaly
by 2, to 5.7GHz.
- 3cm software version :
UNI10PTL
for 3cm ATV TX 13cm frq. must be multiplied externaly
by 4, to 10GHz.
- 64 memory channels available,
EEPROM based. After power_on memory chan. "00" will be selected.
- software name, release
date and version displayed at power ON.
- Real time displaying of
PLL LOCK state and Rx or Tx mode.
- Software supports single
and double line Hitachi compatible LCD's. (1x16, 2x16, 1x20, 2x20, 4x20...).
- LCD can be omit-ed. UNI13P
will operate well without connected LCD and/or keyboard.
- Few power_on commands
build in (toggle LCD type, total INIT, toggle RX/TX mode in dual mode
CPU only).
- Extra reset logic build
in.
- PLL
support for: Philips TSA-5055T, Mitel SP5055S, with additional software:
Siemens SDA-6102.
- Sigle sided, profesional
made PCB sizing 4.5 x 5 cm only.
- Supply voltage from +8
up to +14v.
- Very low power consumption
(6mA @12v).
Functions on UNI13P keyboard:
| UNI13P v2.02 | DOWN | UP | FUNCTION | MEMORY |
| Memory mode : | Memory DOWN | Memory UP | Switch to VFO mode | Read from Memory |
| VFO mode : | Tune DOWN | Tune UP | Switch to MEM mode | Write to Memory |
| KEY+PWR_ON : | (Software info)
Available in previous versions only! |
Toggle
Single / Dual line LCD |
TOTAL INIT
Execute after 1st run ! |
Toggle
RX / TX mode |
Yes, there is more on this issue. Instead of UNI13P processor module, you can controll 23cm & 13cm RX or TX directly from PC. The stand alone PC software called ATV13P.EXE (Win95/98) is also writen. The screenshot can be seen below. Software uses one COM port & simple RS232 / TTL line converter (MAX232 with few parts around). Software for PC supports: TX as well RX modules. Only one module can be connected at time on to I2C bus (there are the same bus addresses inside modules..). Future release: v2.00 ATV13P will support: 23cm RTX, 13cm RTX, 6cm TX and 3cm TX.
ATV13P software will be operational on folowing
modules: any Comtech modules and Conrad AWV314 modules. Note:
ATV13P is build for DESKTOP PC. It won't be operational on all types
of LAPTOP computers!
ATV13P.EXE v1.00 (Win95/98) will give you folowing possibilities:
- RX & TX
13cm modules support with single software.
- One VFO available, with
with freqency range from 2.000 up to 2.700 GHz.
- Few predefined VFO steps
possible: 0.125 MHz, 0.250 MHz, 0.500 MHz, 1.000 MHz, 10.000 MHz.
- 10 memory channels available,
plus VFO memory. After power_on VFO memory is selected.
- Extra buttons for: LOCK
detect, Data Rewrite, and I2C bus scan.
- Free selectable COM port
(1...4)
- All additional software
parameters are saved at press on Quit button. Auto recall on power_on will
occur.
- Only 3 files are needed:
main executable, INI file, and one small DLL file.
2000-03-05
Download ATV13P-demo.ZIP v1.00 Win.95/98 package 2.4GHz
ATV rx/tx
Order
full functional single user Software
Order
RESALEr pack (Software pack + KeyGEN compiler)
UNI13PxL
CPU's & profesional made PCB's are available now ! Source files
(Gerber, Drl, Accell PCB, processor BIN/HEX) available with unlimited reproduction
& trading rights to companies interesting in.
UNIPLL - Universal
PLL
based on PIC 16F84
2001-04-22 Schematic: using SDA6102-5X
PLL on UNIPLL SDA6102.PDF
2000-02-25 Latest doc on UNIPLL &
other S51KQ software UNIPLL.PDF
