Page updated   2004 April 19.
LANC, DV-IN, ANA-IN
 
Specifications and designs are subject to change without notice.
Use on your own risk.   All rights reserved by authors.
 
 
Control_L  -  Digital8 & DV remote control
Stand alone remote control will add RECORD button to digital cam in VTR mode

->

LANC-1  (Assembled, preprogrammed, in box, ready to use) Secure Order

EU models of D8 and DV camcorders don't have DV-IN & ANALOG-IN enabled. This can be done using service tools : RM95, PC95 softwareLremote software, or doit your self with one of free DV-IN tools. After dangerous job is done your D8 camcorder won't support only DV IN on FireWire (IEEE-1394), but ANALOG IN (on normal analog output conn.) too. Ideal for recording analog ATV transmissions, video tests, etc, all in digital mode. But there is no RECORD button in VTR mode on your EU camcorder. At home you can use PC with software for controling. But what can we do on remote locations?  Driving PC with camcorder ?  No, for shure not. The tiny microprocessor remote controller LANC1 will do the job well. With two pushbuttons you can start VTR Recording, and Pause Recording. The same time VTR buttons on camera working too (Stop, Pause, Rewind, Play, ..). Remote controller is compatible with all models of SONY D8 & SE D8 camcorders, most of SONY DV (and miniDV) & Hi8/Video8 camcorders.

NOTE: camcorder must be DV-IN / ANA-IN enabled before LANC-1 remote can be used.
 
 

How to enable LANC-1 for CAM mode

LANC-1 as delivered is ready for use in VTR mode. CAM (camera) and VTR (videorecorder) modes uses different record comand sequences. If you like to use device in CAM (camera) mode, two step  modification is needed. Carefuly open remote (screw on backside). Step 1:  cut (break) PCB line marked with RED on picture. Cut should be at least 1mm wide. Step 2: use wirewraping or similar tiny (isolated) wire and conect REC pushbutton with corner pin (pin10) of LANC-1 CPU, using soldering tool. That's all. Software support for CAM REC mode is already built in any LANC-1 remote. 

Do not try to solder wire without going thru 1.step (cuting PCB line). That way CPU will be destroyed.
Avoid any static discharges !  Device is static sensitive!
 

1999-11-25  S5  LANC - Krmiljenje digitalnih video kamer S5LANC.PDF
1999-11-25  LANC1 - User manual LANC1.PDF

LANC-1  (Assembled, preprogrammed, in box, ready to use) Secure Order



Automatic DV-IN enabling soft. for one camcorder (Digital8 & DV)  Link to Lremote package
Link to AutoPC95 software DV-IN enabling software.


LANC control - PC LPT :  


             Click on picture above. Full operational adapter with BS-170
Make adapter,download software, unzip it, connect camcoder with adapter to LPT1 ( LPT must be drivers free) and run EXE file.

This cable will work on free DV-IN tools, as well on comercial ones.

Part list: 1 x DB25M (male) for LPT, 1 x minijack 2,5" Stereo, 1 x FETtransistor BS170 , cca 1m mono coaxial audiocable (1+GND).
 
ALL IS ON YOUR OWN RISC and for education only!

 

Download folowing  3rd party  free DV-IN software for SONY, PANASONIC, JVC :
 
DVinD8se SONY SE D8, RAM version. DCR-TRV 120,320,520,720,820
v1.01 written by Martin Smola     home page
DVinLITE15
DVinLITE16
DVinLITE17
SONY RM95 emulator 
v1.5 written by Martin Smola     home page
v1.6 & 1.7 with emergency button !!!
ANIN 1.5
ANIN 1.6
SONY D8, RAM version. DCR-TRV 7000,110,210,310,510
v1.6 written by Martin Smola     home page
PANA Test 1.0
PANA Test 2.0
PANA List
PANASONIC Read/Write data out of DV camcorders
written by Michal Krejcik     home page
RM95

** NEW **
RM95EMGY

LANC RM95DUMP for memory DUMPs & RM95EMUL  (DOS)
written by Helge Wagner
Usage: "RM95DUMP > FILENAME.TXT" & use cable above

LANC RM95EMGY emergency program - the same functionality as the "emergency" button of the "DVin lite" program (it will set page 0x02 address 0x25 to 0x80). Sources are included. To build the program, some other files from the RM95 packet are needed.
written by Helge Wagner

JVC-EM 1.1
JVC-EM 2.0 beta
JVC-EM 2.0 final
JVC-EM 2.1 beta
JLIP 1.0 beta
JVC EEPROM & DV-IN  manager for DV camcorders
written by Paulo Ramos     home page

Note: v2.1 is an BETA release, changing daily!
Jump on authors web page for latest one.

Note: JLIP is an debuger   Paulos home page.zip

Video Pages < interesting DV-IN related LINKS
oSamsung info < DV-IN related VP-D55/60/63/70/73/75/77 and similar Medion-camcorders by Wolfi1000
NOTE: only LEGAL - non pirated  software can be hosted here,
info must include valid authors Email & home page.
 
! ! !  DANGER  ! ! !

Second edition Sony D8  cams uses other DV-IN data  & cheksum !

2000-08-23     Q&A-01 :
2000-09-19     Q&A-02 :
2000-10-06     Q&A-03 :
2000-10-08     Q&A-04 :
2001-03-15     Q&A-05 :
2001-06-19     Q&A-06 :
2001-07-17     Q&A-07 :
Enabling D8, DV cam. And if something goes wrong...
Where is the old JVC-IN pack gone ?
How to record in LP mode on to standard 8mm tape ?
How to calculate CHEKSUM on 1st edition D8 ?
DV-in problem. Can you help?
DV-IN enable for the SONY PC4/PC5
Checksum calculator for Sony D8 SE..       XLS file
Camcorders that can not be DV-IN enabled:

Canon MV5, MV500, MV530, MV550
Grundig DLC1505
JVC GR DV1, DV3, DVF1, DVF10, DVJ70, DVL155, DVL160, DVL165, DVL200, DVL365, DVL400, DVL765, DVL865, DVL9000, DVM1, DVM5, DVP1(in service only), DVP3, DVP5, DVX, DVX400, DV500E (in service only)
Panasonic NV DS29, DX1, GS1, MX2
SONY DCR IP55, PC10E, TRV16E, TRV18E, TRV24E, TRV130E+140E (in service only), TRV238E, TRV239E, TRV340E, TRV733E, TRV738E
Thomson VMD712, VMD912

         

CAMCORDER MEMORY DUMP

Do you have any complete camcorder memory dump ?
No? Use RM95DUMP.EXE and drop me a mail.
(attach info about DV-IN state, plus if you grant publishing of your identity)
 
 
DCR-TR7000 D8 TR7000E   before enabling  DV-IN  (factory setup)
TR7000 NTSC (US)  DV-IN enabled  (factory setup)
DCR-TR7100 D8 TR7100E   before enabling  DV-IN  (factory setup)
DCR-TRV210 D8 TRV210E   before enabling  DV-IN  (factory setup)
TRV210E   after enabling  DV-IN, ZEBRA, White bal., etc
TRV210 NTSC   factory setup
TRV210 NTSC   after enabling  ZEBRA, White bal., etc
DCR-TRV310 D8 TRV310     NTSC USA   DV-IN enabled (factory setup)
TRV310E   before enabling  DV-IN  (factory setup)
TRV310E   before enabling  DV-IN  (factory setup2)
DCR-TRV410E D8 TRV410E   before enabling  DV-IN  (factory setup)
TRV410E   after enabling  DV-IN
DCR-TRV510 D8 TRV510E   DV-IN disbled (factory setup)
TRV510     NTSC English  DV-IN enabled (factory)
DCR-TRV8000E SE Sony D8 TRV8000E   before enabling  DV-IN  (factory setup)
TRV8000E   enabled  DV-IN / ANA-IN / pass trough
DCR-TRV8100E SE Sony D8 TRV8100E   before enabling  DV-IN  (factory setup)
DCR-TRV120E SE Sony D8 TRV120E   DV-IN disabled  (factory setup)
TRV120E   DV-IN disabled 2 (factory setup)
TRV120E   DV-IN enabled  (factory setup)
TRV120E   (Australia) DV-IN enabled  (factory setup ++)
DCR-TRV125E SE Sony D8 TRV125E   before enabling  DV-IN  (factory setup)
TRV125E   before enabling  DV-IN  (factory setup)
TRV125E   after enabling  DV/ANA-IN
DCR-TRV320E SE Sony D8 TRV320E   before enabling  DV-IN  (factory setup)
TRV320E   after enabling  ZEBRA patern (no DV/ANA-IN!)
TRV320E   after enabling  DV/ANA-IN
TRV320E   after enabling  DV/ANA-IN, ZEBRA patern
DCR-TRV325E SE Sony D8 TRV325E   before enabling  DV-IN  (factory setup)
DCR-TRV420E SE Sony D8 TRV420E   before enabling  DV-IN  (factory setup)
TRV420E   after enabling  DV/ANA-IN
DCR-TRV520E SE Sony D8 TRV520E   before enabling  DV-IN  (factory setup)
TRV520E   after enabling  DV/ANA-IN
DCR-TRV620E SE Sony D8 TRV620E   DV-IN enabled  (factory setup)
DCR-TRV725E SE Sony D8 TRV725E   before enabling  DV-IN  (factory setup)
DCR-TRV230 TE Sony D8 TRV230E    before enabling DV-IN (factory setup)
TRV230     NTSC   DV-IN enabled (factory setup)
DCR-TRV238E TE Sony D8 TRV238E    before enabling DV-IN (factory setup)
DCR-TRV430E TE Sony D8 TRV430E   before enabling  DV-IN  (factory setup)
TRV430E   after enabling  DV/ANA-IN
DCR-TRV530E TE Sony D8 TRV530E   before enabling DV-IN (factory setup)
TRV530E   after enabling DV/ANA-IN
DCR-TRV730 TE Sony D8 TRV730     NTSC Asia   DV-IN enabled (factory setup)
TRV730     NTSC Asia   additional funct. enabled
TRV730     NTSC USA   DV-IN enabled (factory setup)
DCR-TRV240E FE Sony D8 TRV240E  DV-IN ANA-IN enabled  (factory setup)
DCR-TRV340E FE Sony D8 TRV340E   before enabling DV-IN (factory setup)
TRV340E   2. before enabling DV-IN (factory setup)
TRV6E MiniDV TRV6E   1 before enabling  DV-IN  (factory setup)
TRV6E   2 before enabling  DV-IN  (factory setup)
TRV6E   2 after enabling  DV-IN
TRV7E MiniDV TRV7E   before enabling  DV-IN  (factory setup)
TRV7E   after enabling  DV-IN
TRV8E MiniDV TRV8E   before enabling  DV-IN  (factory setup)
TRV8E   after enabling  DV-IN
TRV9E MiniDV TRV9E   before enabling  DV-IN  (factory setup)
TRV9E   after enabling  DV-IN
TRV9E   after enabling  DV-IN
TRV10E MiniDV TRV10E   after enabling  DV-IN
TRV11E MiniDV TRV11E   before enabling  DV-IN  (factory setup)
TRV15E MiniDV TRV15E   before enabling DV-IN (factory setup)
TRV15E   after enabling DV-IN
TRV17 MiniDV TRV17  NTSC (US)  DV-IN enabled  (factory setup)
TRV20E MiniDV TRV20E   DV-IN enabled  (factory setup)
TRV900 MiniDV TRV900  NTSC (US)  DV-IN enabled  (factory setup)
PC1E MiniDV PC1E   before enabling DV-IN  (factory setup)
PC2E MiniDV PC2E   before enabling DV-IN  (factory setup)
PC2E   before enabling DV-IN  2 (factory setup)
PC2E   after enabling DV-IN  2
PC3E MiniDV PC3E   after enabling DV-IN
PC4E MiniDV PC4E   before enabling DV-IN  (factory setup)
PC5E MiniDV PC5E   before enabling DV-IN  (factory setup)
PC5E   after DV-IN  enabled
PC5E   2-before enabling DV-IN  (factory setup)
PC5E   2-after DV-IN  enabled
PC6E MiniDV PC6E   before enabling DV-IN  (factory setup)
PC6E   after DV-IN & Zebra  enabled
PC7E MiniDV PC7E   after DV-IN  enabled
PC100E MiniDV PC100E   factory enabled  DV-IN
PC110E MiniDV PC110E   factory enabled  DV-IN
SC100 MiniDV SC100 NTSC  factory enabled DV-IN
DCR-VX700E MiniDV VX700E  PAL   before DV-IN enabled  (factory setup)
VX700E  PAL   after DV-IN enabled 
DCR-VX1000 MiniDV 
3CCD
VX1000  PAL  ser.nr.12xxx   DV-IN enabled
VX1000  PAL  ser.nr.218xx   after DV-IN enabled 
VX1000  NTSC Japanese  DV-IN enabled (factory)
VX1000E  PAL  ser.nr.363xx   before DV-IN enabled 
VX1000E  PAL  ser.nr.363xx   after DV-IN enabled 
DCR-VX9000 Full sizeDV 
3CCD
VX9000  PAL  before DV-IN enabled & howto enable! 
CCD-TRV65E Hi8 TRV65E   before enabling  ANA-IN  (factory setup) + code
CCD-TRV66E Hi8 TRV66E   before enabling  ANA-IN  (factory setup)
TRV66E   after enabling   ANA-IN
CCD-TRV94E Hi8 TRV94E   before enabling  ANA-REC  (factory setup)
CCD-TRV940 Hi8 TRV940  NTSC  (US)  ANA-IN enabled (factory setup)
CCD-TR3000 Hi8 TR3000  NTSC English  ANA-IN enabled  (factory setup)
CCD-TR3300 Hi8 TR3300E  before  ANA-IN enabled  (factory setup)
JVC GR-DVX 7 JVC  MiniDV JVC GR  DVX 7  DV-IN enabled  (factory setup)
JVC GR-DVL107 JVC  MiniDV JVC GR  DVL 107  DV-IN enabled  (factory setup)
JVC GR-DVL150 JVC  MiniDV JVC GR  DVL 150   after DV-IN enabled
JVC GR-DVL355E JVC  MiniDV JVC GR  DVL 355E   before enabling  DV-IN ( factory setup)
JVC GR  DVL 355E   after DV-IN enabled
Panasonic DS-99 MiniDV PANASONIC DS-99  after DV-IN enabled

If you grab these DUMP files for your ftp or html server, be at least so honest to drop me a note.


Temporary enable COLORBAR (Zebra patern) on any SE D8
(TRV8000E, 120E, 320E, 520E, 620E, 820E)

1.-   switch camcorder in to CAMERA mode
2.-   page 00  adr 01   set from 00 to 01  And DON'T EXECUTE  STORE command !
3.-   page 0D  adr 1E   set from 24 to A5  And DON'T EXECUTE  STORE command !

New option called COLORBAR became visible in camera menu OTHERS.
Switch option ON and Colobar is there. Until... you disconnect your power supply.
No risiko - all changes hapend in RAM area only.


Enable COLORBAR (Zebra patern) on  Cannon XL-1

1.-   Turn the dial to the "green rectangle" which is auto everything.

2.-   On the little arm that hangs down on the left side of the camera there are 
two buttons that control the shutter speed. Hold those two buttons 
down for approx. 5 seconds and you got bars.

3.-   To turn them off, hold down the same two buttons for approx. 5 seconds.

They are not SMPTE bars and are not extremely accurate for the colors they represent.
They are only a rough approximation.


 

SE D8 remote info:  EU RMT-814 can be enabled for VTR REC

RMT-814 seems to use the same hardware as RMT-808 (on right side)
NOTE:  S51KQ's  LANC-1 remote will operate on SE D8 very well, too.

 


 


Enable SAMSUNG VP-D55/60/63 or Medion (Aldi)  MiniDV cam (thanks to Wolfi1000)
This is a procedure that works for the Samsung VP-D55/60/63 I have 
also (different) infos for VP-D70/73/75/77 and similar 
Medion-camcordersor Medion (Aldi) MiniDV cam and should be similar for others (but take care!) 

1. switch on your camcorder in playmode (a cassette should be inside) and look at the TFT-display. 
2. Press "Play" and "Down" buttons at the same time (at the side of the camera below "Enter") to get into service mode ;-) 
3. Press "Stop" to prevent the tape from running further 
4. Take your remote controll and press the red button until "OPTIONS" is shown on the screen. 
5. Write down the HEX number which ist shown behind options in case you want to switch back later. 
6. Now press "Wide" or "Tele" on your remote controll to increment or decrement the Hex number to "FE"
7. Press the red button again to store the number
8. Disconnect your camara from all electric sources (e.g. battery or plug) 

... and you're done! 

My remarks: The Down-Button for the VP-D55 is under the TFT (Up/Enter/Down..). You have to press the Play + Down Button for 10 seconds to switch in to service mode.

Samsung VP-D55/60/63/70/73/75/77 and similar Medion-camcorders, service manuals on http://free.hostdepartment.com/w/wolfi1000/samsung.html

S51KQ note: instead of original IR remote you can try to use remotes from other Samsung MiniDV cams.




 

3rd party  DV-IN  CODES
Not all verified by S51KQ

Be careful by using PAL codes on NTSC models !
After changing the codes, switch the camera off, remove battery and pull_out LANC cable !

All changes & modifications are on Your own risk !


1st edition D8 :  TR 7000E, 7100E, 110E, 210E, 310E, 410E, 510E

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 A1 A3 enable record
D 15 18 1B enable DVin
D 27 22 23 cheksum
0 01 01 00 install write protection

Other functions on TR 7000E, 7100E, 110E, 210E, 310E, 410E, 510E

Note: TR7000E & 7100E uses different  data on adr. 1E & 20 (green area)
Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 A1 A3 enable record
D 17 77 F7 enable gain & exposition changing
D 18 40 60 Zebra warning patern if overexposed 
D 1E 89 8B enable White balance mode (auto/indoor/outdoor/hold)
D 1E 88 8A enable White balance mode (auto/indoor/outdoor/hold)
D 20 0F 1F LaserLink function
D 20 0B 1B LaserLink function
D 23 00 3B cheksum
D 24 01 19 enable Frame & Interval rec 
D 25 00 81 enable Colorbar in cam mode
D 26 00 10 enable DV-editing function
D 27 22 23 cheksum
0 01 01 00 install write protection

 

2nd edition D8 :  TR 8000E, 120E, 125E, 320E, 520E, 620E, 820E   Tested on TRV 320E, only

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 24 26 enable record & DV/ANA in
D 23 A9 AB enable White balance control
D 2C 22 63 (TRV 320E ) OK
26 (TRV 120E,125E) ??
cheksum  Depend on other existing data too!
0 01 01 00 install write protection
Note: Please send me reports if you find these codes to be operational on other type of SE D8 cameras.
 

3rd Edition D8 - other functions on TRV 730  NTSC (Asia)

Henry Y. wrote:  I have succeeded in modifying TRV-730 (Asia). A lot of changing method and address is similar to TRV-x20 series and the checksum compensation address is 2A (in page D).
 
Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 16 07 17 Interval REC (Frame REC not fonduded)
D 17 18 48 WIND
D 1A 37 B7 Manual exposure value display
D 1B 40 60 Zebra
D 1E 34 B5 Colorbar
D 23 B9 BF White balance & Mic
D 2A 00 67 cheksum compensation
0 01 01 00 install write protection

 

PC1E

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 24 26 enable DVin 
D 15 B8 BB enable record
D 27 02 03 cheksum 
0 01 01 00 install write protection

 

PC2/3E

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 24 26 enable DVin
D 15 38 3B enable record
D 27 12 13 cheksum 
0 01 01 00 install write protection

 

PC4E  - Other functions on PC4E

 
Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 16 06 0E enable Frame Rec
D 1B 40 60 enable Zebra
D 1E 64 E5 enable Colorbar
D 23 0B 0F manual Mic gain
D 2C 13 13 enable ESP/ELP recording modes (Already on?)
D 29 40 4C enable new Memory stick recording mode (Not applicable to PC4)
D 31 00 A1 checksum
0 01 01 00 install write protection

Your site has table of codes for the PC5E. Being highly interested in these features, I (Mattias Hult) decided to give it a try on my PC4E, which is identical to the PC5E except for memory stick. The codes worked fine in RAM mode, but when I tried them in EPROM the camcorder locked up. Thanks to Martin Smola's excellent DVin lite unlocking it was easy. Since the codes worked in RAM, I figured it was a problem with the checksum. Also, D:2C was set to 13 from the beginning in my camcorder, and not to 12 as was stated in your table. After some trial and error, I managed to get it working with the checksum set to A1. So, for PC4E, the table should look like shown above.

I realise that this might not work with all PC4Es. In case of trouble, one should experiment with different checksums. This is (relatively) easy with the convenient emergency feature in DVin lite.
 

PC5E  Atention: the Cheksum code is missing here

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 24 26 enable DVin
D 15 01 03 ??
0 01 01 00 install write protection

Other functions on PC5E

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 16 06 0E enable Frame Rec
D 1B 40 60 enable Zebra
D 1E 64 E5 enable Colorbar
D 23 0B 0F manual Mic gain
D 2C 12 13 enable ESP/ELP recording modes
D 29 40 4C enable new Memory stick recording mode
D 31 00 A7 cheksum ??
0 01 01 00 install write protection
ATTENTION: Avant d'éteindre le camescope bien s'assurer que les datas F0 et F1 de la page 2 soient respectivement à D5 et 04. (2:F0=D5 et 2:F1=04)
 

PC5E  Another posibility to get permanent DV-IN    Drop me a note if works on your camera.

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 24 26 enable DVin
D 2C 12 13 enable ESP/ELP recording modes
D 31 00 03 cheksum ??
0 01 01 00 install write protection

PC7E

Page Adress Original Data Modified Data Action
1 00 00 01 remove write protection
D 14 44 46 enable DVin 
D 1C 11 13 enable record
1 00 01 00 install write protection

Digital Zoom to 90 (120 ?)

Page Adress Original Data Modified Data Action
6 00 00 01 remove write protection
F 1B CD CF larger digital Zoom
6 00 01 00 install write protection

 

TRV5E

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 4E 4F enable DVin
D 15 81 83 enable record
D 1A 73 70 cheksum
0 01 01 00 install write protection

 

TRV6E    Temporary enable DV-IN

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 24 26 Don't press on STORE !
D 2C 12 13 Don't press on STORE !
0 01 01 00 install write protection

 

TRV7E

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 56 57 enable record
D 15 01 03 enable DVin
0 01 01 00 install write protection

 

TRV9E

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 5E 5F enable record
D 15 81 83 enable DVin
D 1A 73 70  
0 01 01 00 install write protection

 

TRV 8E / 10E

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 24 26 enable record
D 15 38 3B enable DVin
D 27 12 13 cheksum 
0 01 01 00 install write protection

Other functions on TRV 8E / 10E

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 18 40 60 enable Zebra
D 1E 8B 8F manual Mic gain
D 24 01 19 enable Interval & Frame rec
D 29 BF 83 cheksum
0 01 01 00 install write protection

 

TRV890E

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 25 27 enable record
D 15 38 3B enable DVin
D 27 42 43 cheksum
0 01 01 00 install write protection

 

SC100

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 16 17 enable record
D 15 01 03 enable DVin
D 1A 71 F1  
D 21 40 C0  
0 01 01 00 install write protection

 

VX700E / VX1000E

Page Adress Original Data Modified Data Action
1 00 00 01 remove write protection
D 11 44 14 enable DVin and record
1 00 01 00 install write protection

Change Infrared Remote Control code to VTR2

Page Adress Original Data Modified Data Action
1 00 00 01 remove write protection
D 03 00 40 change to VTR2 code
1 00 01 00 install write protection

 

VX9000E

Page Adress Original Data Modified Data Action
1 00 00 01 remove write protection
D 11 84 14 enable DVin and record
1 00 01 00 install write protection

 

DSR200P

Page Adress Original Data Modified Data Action
1 00 00 01 remove write protection
D 11 C4 54 enable DVin and record
1 00 01 00 install write protection

 

CCD-TRV65E  Hi8

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 64 66 enable record
D 21 00 02 cheksum
0 01 01 00 install write protection

 

CCD-TRV87E  Hi8

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 14 65 67 enable record
D 1E A9 AB enable ANAin
0 01 01 00 install write protection
Note: Codes out of the DCR-TRV110E set were used to enable this camera.  You can use the LANC1 or a remote commander with REC function to start the recording, ofcorse in player mode. You can also use a button placed on camcorder for starting the recording. This button must be between to pin 93 of IC803 of the VC-234 board and with 4,7K resistor to ground. The button must be pushed at least 1 sec. to start recording.
 
 

TR780e  Hi8

Page Adress Original Data Modified Data Action
0 01 00 01 remove write protection
D 17 06 17 enable record
D 15 18 1B enable ANAin
D 27 22 23 cheksum 
0 01 01 00 install write protection

 

PANASONIC camcorder (use PANATEST 1)
 

Model Page Address Code En. Code Dis. Comment
DS77 0 F8 42 42 Identification
  0 F7 01 or 81 19 or 99  
  0 30 23 33
DA1 0 F8 62 62 Identification
  0 F7 00 18  
  0 30 EF FF
DS33 0 F8 72 72 Identification
  0 F7 01 19  
  0 30 23 33
EX1 0 F8 82 82 Identification
  0 F7 01 19  
  0 30 23 33  
DX100 0 F8 A2 A2 Identification
  0 F7 00 18
DS5 0 F8 B2 B2 Identification
  0 F7 00 18
DS1 0 F8 C2 C2 Identification
  0 F7 A0 B8

 

For camcorders below use PANATEST 2
 

Model Page Address Code En. Code Dis. Comment
DS99 0 F7 A0 A0  
  0 DD 2C 3C  
  1 97 02 12
DS11 0 F7 68 68  
  1 97 03 13
EX3 0 F7 A0 A0  
  0 DD 2C 3C  
  1 97 02 12
DS8 0 F7 68 68  
  1 97 83 93
DS35 0 F7 A0 A0  
  0 DD 2C 3C  
  1 97 02 12
DS55 0 F7 A0 A0  
  0 DD 2C 3C  
  1 97 02 12
DS15,DS25 0 F7 A0 A0  
  0 DD 2C 3C  
  1 97 07 17

Back to HARDWARE area

| Top | Home | E-MAIL | What's NEW |
| ATVS | REPEATERS | DVMS | NET | PACKET RADIO | BROADCASTING |
| HARDWARE & SOFTWARE | DV-IN | DV-NLE | CD | VIDEO|
This page is maintained by: Mijo K., S51KQ